BET Measurement for Enhanced Rubber Quality
The BET (Brunner-Emmett-Teller) theory is used to measure the surface area of solid or porous materials to determine the number of molecules/atoms of a gas needed to form a monolayer, Xm, of adsorbed gas on a solid surface. BET studies give important structural information on the material’s physical structure as the area of its surface affects how that solid will interact with its environment. The BET method is commonly applied to calculate the specific surface area on the basis of nitrogen adsorption isotherm measurements at 77 K.
The rubber and tyre sectors use a broad variety of synthetic rubber. Butadiene, butyl rubbers, and styrene butadiene are the primary basic ingredients used to make these synthetic rubbers. The tyre sector alone consumes between 70 and 76% of the synthetic rubber produced worldwide. Tires are typically made of various raw materials such as polymeric material, additives, vulcanization agents, fillers, and softeners. Testing of these materials before the formulation of the main product is mandatory. Selecting the raw materials to achieve the required high quality finished product is a great concern.
Fillers are the component that needs to be tested the most because of their special properties. Fillers must have close contact with the elastomer chains in order to help reinforce the rubber product. The size, surface area, surface activity, and shape of the particle complex are the main aspects that these fillers influence. Surface activity is related to the elastomer's capacity to adhere to the filler and the filler's suitability for a specific elastomer. Functional fillers transfer applied stress from the rubber matrix to the sturdy and inflexible mineral. The necessary information about the fillers—which have a large surface area and larger contact area accessible for a higher potential to reinforce the rubber chains—will be provided by BET measurements.
Determining BET measurements
An area of localized stress is introduced by the BET measurements, which are a key factor in determining the polymer interchain distance. Examples of these parameters include porosity and particle size. The elastomer chain rupture during bending or stretching can also be computed. The selection of particles is based on the fillers' sizes rather than their ability to reinforce and will be determined by the BET values. For example, fillers with particle sizes larger than 10,000 nm (10 μm) are normally avoided as they have the potential to degrade performance rather than to extend or reinforce strength. The truly reinforcing fillers, which range from 10 nm to 100 nm (0.01 to 01 μm), can greatly improve rubber qualities. Fillers with particle sizes between 1,000 and 10,000 nm (1 to 10 μm) are usually utilized as diluents and have no significant effect on the rubber properties.
The general impact of each of the three filler features on rubber properties can be broadly summarized as follows, taking into account fillers with sufficiently small particle sizes to offer some degree of reinforcement: Lower resilience and increased Mooney viscosity, tensile strength, abrasion resistance, rip resistance, and hysteresis result from lowering particle size and increasing surface area. Picking the right fillers is crucial because they have the right combination of small particle size, high surface area, high surface activity, and high aspect ratio to prevent the spread of microcracks and provide the increased tensile strength needed to withstand failure.
Reinforcing Fillers
The selection of fillers possessing the aforementioned physical attributes is of utmost importance when choosing raw materials in order to determine the optimal reinforced strength. In the rubber business, silica and carbon black have long been recognized as reinforcing fillers. Their inclusion in rubber is necessary to produce items that last longer, stronger and more durable tires, and—especially in the case of silica—lower greenhouse gas emissions from the automobile industries that utilize these rubbers with composition of above fillers.
To obtain nitrogen adsorption isotherms, the fillers are evacuated at a fixed temperature at a predetermined time before being exposed to nitrogen gas at the liquid nitrogen temperature. Using the BET equation, the BET and c values are determined from the isotherms.
The Barrett-Joyner-Halenda (BJH) method is applied to compute the pore volumes (Vmeso) of the filler samples. The fillers' surface area is determined by using the Brunauer-Emmett-Teller equation (SBET) to the nitrogen adsorption isotherms. This formula has been traditionally employed to indicate the fillers' aggregate structure and particle size. While the surface area can be calculated using a variety of techniques. There are times when cetyltriammonium bromide (CTAB) absorption is a better indicator of the true surface area accessible to big rubber chains. In contrast, the aggregated state of the fillers in terms of the accessibility and diffusion of the rubber molecules is reflected in the volumes of micropores and mesopores. The interaction between the adsorbate and the surface is reflected in the c value that is obtained from the Brunauer- Emmett-Teller plots. Strong adsorption of the adsorbate on the surface is indicated by a high c value. As a result, the computed values of SBET and c are sufficiently rational. The high linearity of the BET plots will be produced from the adsorption isotherms of nitrogen on the fillers showed that their adsorption of nitrogen satisfied the assumption for the BET equation.
Based on the needs and applications of the end user, BET measurements will be very helpful in selecting suitable fillers for the formulation of rubbers in order to achieve excellent performance for all test parameters stated above.
Cotecna Ensures Accurate BET Measurement Results
At Cotecna, our raw rubber materials testing laboratories are required to provide precise BET readings in terms of surface area, particle size, pore volume, STSA, adsorption energy of the pore structure, isotherms, and other areas where precise data is needed to improve the reinforced properties. We test various fillers including Silica, barium sulphate, calcium carbonate, carbon black, hard clays, and other materials can be categorised as non-reinforcing, semi-reinforcing, or strongly reinforcing fillers. It's crucial to choose a rubber raw material testing laboratory with rigorous standards and national accreditations when assessing the rubber's quality. In order to maintain high quality control and meet the organization's criteria.
Testing of raw rubber materials, such as fillers, is crucial for producers to ensure the quality of their rubber products. In particular, important rubber applications like medical O-ring seals and rubber aircraft parts requires rigorous standards of quality control to guarantee that clients receive the best performing rubber goods that meet their expectations. Despite its strength and durability, rubber is impacted by its surroundings over time. Evaluating the material quality of a rubber product requires knowing how it will function under end-use conditions. Rubber is not appropriate for low-temperature applications, for example, if tests on the material show that it becomes brittle at low temperatures even though it is strong at ordinary temperatures. Because of this, the analytics and testing of rubber raw materials are specific to each product and application. The objectives of the product and the industry will determine the best testing strategy. It's critical to comprehend the properties of fillers under particular circumstances before using them in their final form.
In addition, the lab verifies the particle-matrix compatibility, surface activity, shape, and size for the purpose of choosing raw materials for rubber manufacture based on the test results. Along with using top-notch technology and traceable standard CRMs, Cotecna ensures that the lab produces consistent, accurate findings for all ASTM-classified fillers, including N110 to N991 (CB) and N220, N330, N550, N765, and N990 for non-black fillers.
The Cotecna Material Testing Lab is a top-notch facility that offers insightful information about your rubber products. Our team of experienced personnel and lab is accredited by ISO/IEC 17025, ISO 9001, and ISO 45001. We never take our past successes for granted. We place a high importance on effective communication, operate with integrity, and establish bonds with people via our enthusiasm for innovation and common objectives.
To learn more about rubber testing or to request a quote, please contact us.
Latest News
19.11.2026
Political Changes and an Evolving Regulatory Landscape: How Phytosanitary Compliance Can Drive Agribusiness Growth
Discover how Agronômica helps agribusiness companies navigate phytosanitary requirements, reduce export risks and seize new market opportunities.
13.11.2026
ESTS Approved as Higg FDM Validation Body, Expanding One-Stop Higg Sustainability Service Portfolio
We are pleased to announce that Extensive Standard Technical Services Co., Ltd. (ESTS), part of the Cotecna Group, has obtained official approval to deliver Higg FDM (Facility Data Manager) validation service. This extends ESTS’ existin...